You might be remodeling or you might be installing a new shower. So you are wondering: Height of Shower Valve? Shower valve/s placed to high or low will prove to be a huge ergonomic burden. Thus it is imperative to read this guide before making the call. ADA (Americans with Disabilities Act) Human length variation Also consider with children using the shower, a valve placed too high, plus the playful nature of a child, will equal a head bumped on the valve. As some valves have relative sharp angled control knobs, there will be an extra shower … The tears of a crying child. Well if you are the owner of the shower, I suppose you can choose any height that may please you. But… If you are considering other people who might also use the shower, you might want to use the ADA (Americans with Disabilities Act) Shower Valve Measurements Requirements.

[ps2id id=’ADA (Americans with Disabilities Act)’ target=”/]

Height of Shower Valve? – ADA Shower Valve Measurements Requirements.

If you are considering other people who might also use the shower, you might want to use the ADA (Americans with Disabilities Act) Shower Valve Measurements Requirements.

Height Above Floor.

Shower controls area minimum height above the floor is 38 inches above the floor. The maximum height above the floor is 48 inches. Height of Shower Valve [ps2id id=’Human length variation’ target=”/]

Height of Shower Valve? – Human length variation

The tallest member of the household should not have to bend to take hold of the shower valve/s. An older member might have difficulty standing in the shower because of weak feet or legs. This member might want to sit on some chair inside the shower. Thus he/she should still be able to reach the shower valve/s. Also consider looking up your local building codes, as not all towns and cities have laws regulating the installation of shower valves. If building codes don’t regulate the location of your valve, place it in a spot that is easy for everyone to access. A good rule of thumb: for Height of Shower Valve: Install the valve/s between 36 and 48 inches above the shower floor. A height of 28 inches, or 2 feet 4 inches, is standard for valves in bathtub shower units.

Adjustable height shower valve

Adjustable height shower valve installation is an upgrade that will change your showering life.

A shower valve with a height adjustment can lift the spray from your feet all the way up to your head, making it easier to rinse off shampoo and conditioner. It can also make cleaning elderly loved ones or people with back problems much easier as they just need to take a few steps in any direction to get wet. In addition, adjustable height shower valves make for healthier rinses because everyone has the opportunity for an even rinse of every part of their body without fear of accidentally getting sidetracked by where they are bending over, crouching or standing.

The average height for a regular American male is somewhere between 5’7″ – 5’8″. The average female is somewhere around 5’4″ – 5’5″.

There are a few different ways to adjust the height of your adjustable height shower valve. You may have to have it professionally installed by a licensed plumber or do-it-yourselfer. Here are some options that you may consider:

1. Nail Height Adjustment: This option involves grinding your existing valve down and then putting in a new one with the correct replacement screws. Afterward, you will need to replace the plate that your current valve sits on with an adjustable height plate designed for your specific faucet or shower head. This will allow you to make your own personalized height adjustments.

2. Screw Height Adjustment: For this option, the exact same screws that hold your current valve in place are used on the new one. The new valve is simply screwed into this hole in a way that allows it to adjust. You may find it easier to have a licensed plumber install your new valve and then make your own adjustments at home after the installation is complete.

3. Manually Operated Mechanism: This option relies on either common hand tools, or a mechanical inverter that is able to lift up or down as quickly as you can pull or push the appropriate lever or pull-chain (depending on your model). These are manual gears and pulleys that are either built into your valve, or they are added on after the fact.

4. Self-Cleaning Mechanism: These types of adjustable height shower valves have a self-adjusting mechanism where the valve itself moves up or down as you move your shower head back and forth. This is ideal if you want to rinse off under the spray of a fixed point in the shower rather than having to reach out and raise it yourself.

5. Commercial Options: Some commercial options use an attachment that allows you to mount your adjustable height shower valve onto your wall, above the actual shower head. This allows you to bypass the problem of having to step over or crouch down and make your adjustments.

How to unclog a shower drain with standing water

Shower Heights | Clearances

You replace your old shower head with a new one and everything seems to be working just fine. Then you notice that the water is not spraying out as high anymore, or it feels like you are bending over, and then it hits you: your height of shower valve pipe is too short.

To get the right height for your new head, follow these steps:
1) Measure from the ground to where your hand touches when using both arms to try to spray as much water as possible.
2) Next measure from the ground to two inches below where the spout of your new head will be sitting (you’ll want about 18″ clearance).
3) Measure from the ground to where your hand touches when you are standing straight up.
4) Measure from there to where the water will be hitting your back (18″ for a 1″ shower head, probably several inches less for other sizes).
5) Move your hands in front of you until they touch each other. Your hand should be at about the same height as your shoulders, but if not, continue moving both hands outwards until they touch each other.
6) Finally, you need to figure out how much extra pipe you need to cut. If you used the instructions above, then the pipe will be too short. Use the chart below to figure out how much extra pipe you need to add:

Theoretically, an 18″ tall person should have a shower head that is a little more than 24″ from where it attaches to the shower arm. This is because in addition to the water hitting them in the back, they want water spraying directly on them for a little extra lift (and because they are over 5′ tall). For most American homes this is not possible, due to pipe height restrictions. Most walls are only 9’+ high and require additional clearance for support beams and HVAC equipment. This is a good thing. In fact, you should make the extra effort to clear the pipe and be sure that it is big enough to handle all your showering needs.

Drainpipe Check | Spray Liner

1) Measure up from the floor in front of your current shower head.

2) Measure across from side to side (face of drain).

3) Add 3″ to both sides, plus 1″.

4) Add an additional 6″ if you have a 3″ or 4″ spray head on it.

5) Add another 1-3 inches to the bottom of the drainpipe if your new showerhead requires that (ie: taller people‘s showers).

6) Add an additional 3″ for any sprayers you have.

7) Measure from wall to wall to make sure that your drainpipe will slide along the wall when installed.

8) If you cannot find your line on the chart, check the plumbing in your home. If it is a metal pipe, then one of your neighbors might do it for you (although avoid doing this).

Showerhead Adjustments | Height of Shower Head

1) Install new showerhead with tapered threading on shower arm pipe before turning on water.

2) Hold shower nozzle in place while turning water on.

3) Adjust nozzles higher than normal to begin with and then lower once water begins to run out slowly after initial adjustment.

4) Check sprayers to make sure that they are also at the right height.

5) With your new showerhead, you might want to adjust your knob to a water pressure setting of between ‘1’ and ‘2’.

6) The flow control on your shower head is for making minor adjustments once everything is flushed. Set the water pressure between ‘2’ and ‘3’ for normal water usage\

7) After a few days of using your new showerhead, let it run while not in use. This will give you time to make any necessary adjustments.

8) Once properly adjusted, leave the nozzles in place but with the flow control off. This will save you water without having to spend time constantly readjusting them.

Horizontal shower grab bars

Horizontal shower grab bars need to be mounted at a height of 36”-42” for people with disabilities, but the height of your shower valve is what determines the average. The valve should be no lower than 27.5 inches off the floor, or about 78% of your height and no higher than 36 inches off the floor, or 110% of your height. If you are tall then you will want to have it set just below your shoulders when standing in the tub; if you are shorter than it should be up by your chin when standing in the tub and taken down one notch from that point during seated washing time (54″). Your hand will be just over the toilet when it comes to your face so you should install a grab bar at an angle between 30 and 45 degrees.

You will also want to be sure that the shower head is mounted no lower than 40 inches from the floor. That way you won’t have to bend down too far every time you want to wash yourself or someone else in the shower. The shower head can be installed higher, but you run into problems with water getting all over the bathroom if it is raised too high. The next time you set up your shower, think about the height and direction of the shower head. You may want to install a mirror so you can use it to look up and check your hair or body for lice or other critters.

The width of the shower should be about 30 inches from wall to wall; this allows a comfortable space for those who are shorter than average in the tub area as well as those of us who are taller than average as we get out. As mentioned above, there will be plenty of room at this height for someone in a wheelchair so you won’t have to worry about them banging their knees on something when trying to exit or enter the shower.

One thing you may not have considered when thinking of handrails is how much space is in the shower. If you are short maybe you don’t need a 30″ wide bench – just put in a 24″ wide one and put a stool on the other side. This will give you room to move around without bumping into each other or into the walls. If you are taller than average then remember that this space can be useful for your needs, too. If your partner is shorter than average then this wider bench will give them room to spread out all their stuff while they take a bath.

Keep in mind that the space underneath the sink of your wheelchair accessible bathroom should also be large enough. The space under or around a sink for a wheelchair needs to be at least 16″ x 24”. This way there is room for someone in a wheelchair to maneuver their chair and/or transfer from the chair to the counter top. What can you do if you don’t have enough room under the sink? One solution is to put a cupboard over it; this will give you some extra storage space that most people never use and allows the wheelchair user extra room underneath. You can also put an extra towel rack or toilet paper dispenser over it, too. This will also allow your partner to move around in the bathroom and get items off the counter without bumping into each other.

If you are short, then you need to make sure your wheelchair accessible bathroom is well lit. If it is dark then you may not be able to see where you are going or what is in front of you. If it’s dark, are there any way to add more light? Even a dim wall light over the toilet or on the door would do wonders for making it easier for your partner to maneuver when they are getting ready in the morning.

Statistics

  • A clear space of 30 inches in front of the lavatory is recommended for comfortable use of the fixture, according to NKBA Bathroom Planning Guidelines. (supplyht.com)
  • The toilet paper holder should be 8 inches to 12 inches in front of the toilet and 26 inches off the floor, according to NKBA Bathroom Planning Guidelines. (supplyht.com)
  • The minimum distance is 15 inches from centerline of the lavatory to the wall, according to building code, providing only about 2 inches from the edge of the average lavatory to the wall or obstruction. (supplyht.com)
  • The recommended clearance in front of a tub is 30 inches, according to NKBA Bathroom Planning Guidelines. (supplyht.com)
  • Shower controls should be placed 38 inches to 48 inches off the floor, according to NKBA Bathroom Planning Guidelines. (supplyht.com)
  • I’m fighting with as I can’t seem to find a 100% right answer to some guidelines . (terrylove.com)
  • Videos Users 92% of readers found this page helpful. (askinglot.com)
  • Plus, get an extra 20% off with (finehomebuilding.com)

Sources

The code requirement for the centerline distance is 30 inches. (supplyht.com)

Shower heads are located at a standard height of 80” (203 cm), but can be set at a minimum height of 72” (183 cm) if desired. (dimensions.com)

For shower stalls, install the valve at the standard height of 48 inches, or 4 feet. (askinglot.com)

National Kitchen & Bath Association provides this chart for shower head height based on users’ height. (homedecorbliss.com)

For a person to move out of the shower spray inside the shower, a 42-inch x 36-inch shower should be considered. (supplyht.com)

Shower valve height I take into consideration everything, such as the customers height, or if in a apartment, I base it off me. (ridgidforum.com)

Hold the slide bar in position against the shower wall with its bottom end about 52 inches above the tub floor. (That placement allows you to adjust the showerhead from about 52 inches to 76 inches high, which will accommodate most people.) 23 Related Question Answers Found What height should a shower mixer be? (askinglot.com)

If you have multiple people of varying heights in the home, average the heights and choose the appropriate height for the average while ensuring that the tallest person will not inadvertently hit his or her head on the showerhead. (homedecorbliss.com)

A handheld shower may be used in place of, or in addition to, the fixed showerhead to offer the user flexibility. (supplyht.com)

For shower stalls, install the valve at the standard height of 48 inches, or 4 feet. (askinglot.com)

However, there are standard heights for shower heads that … (bathroomx.blogspot.com)

My last customer 6′ would have been about arm pit high :laughing: KillerToiletSpider The Grand Wazoo On most of our jobs the architect specifies valve heights, on a shower it is usually 40″ for the thermostatic valve, 48″ to the control valves, 40″ for the hand shower, 84″ for the showerhead, 24″, 36″, and 48″ for the body sprays. (contractortalk.com)

Shower controls should be placed at a height 40”-50” (102-127 cm) above the shower floor and out of direct line of the water path to avoid being caught in extremely cold or hot water when operating. (dimensions.com)

If your shower has separate handles for the hot and cold water controls, place these handles 8 inches apart from one another on a straight line — one 4 inches to the left of the valve and one 4 inches to the right of the valve. (bathroomx.blogspot.com)

Codes require that shower control valves must be either pressure balanced, have thermostatic mixing, or have a combination of both, to prevent scalding due to changes in water pressure. (supplyht.com)

Toilet Clearance in Relation to the Shower Though it may not seem obvious, most local codes have standards when it relates to the distance between the shower and toilet . (upgradedhome.com)

Shower seats, toilet placement, and toilet clearance are just a few of the things that one would have to consider in a DIY venture. (upgradedhome.com)

If the bather will be transferring from a wheelchair or other mobility aid to the shower, a 36-inch x 48-inch space is a minimum requirement, with more space preferred. (supplyht.com)

Height of Shower Valve?