Is your shower head not performing like it used to? You may wonder how to clean your shower head. Over time mineral deposits can build up which can cause the nozzles to squirt water in all directions or clog up completely, leaving you with poor water pressure or low flow. So how to clean a showerhead with vinegar? In this article we will discuss how long to soak shower head in vinegar and how to clean your showerhead with vinegar and baking soda.
Page moved here from our other website “Shower Eden“
How to clean a showerhead with vinegar?
- Remove your showerhead by turning it counterclockwise until it comes off the wall pipe. If you are unable to unscrew it by hand, loosen it with an adjustable wrench, but first wrap the fixture with a rag to prevent scratching the finish.
- Place your showerhead in a large pot. Add enough distilled white vinegar to completely submerge the fixture and allow it to float in the liquid. How long to soak shower head in vinegar?
- Allow your showerhead to soak in the vinegar. The acid in the vinegar should penetrate and dissolve any mineral deposits clogging up the spray holes.
- Remove the showerhead from the vinegar the following morning. Clean off any loosened mineral scale with an old toothbrush or scrub brush. Poke the spray holes with a toothpick or a very thin wire to clean out any remaining gunk. Rinse the fixture thoroughly under running tap water.
- Reinstall your showerhead. Apply fresh plumbing tape to the threads of the wall pipe, wrapping it counterclockwise four or five times. Screw your showerhead back onto the pipe.
- Turn on the cold tap water and run it through your showerhead for a few minutes. This should blast out any remaining mineral deposits and vinegar residue. Check for leaks and tighten your showerhead, if necessary.
- Pour distilled white vinegar into a sturdy plastic baggie large enough to completely submerge your showerhead. Wrap a strong rubber band around the baggie to keep it securely attached to your wall pipe. How long to soak shower head in vinegar?
- Allow the fixture to soak in the vinegar. Remove the baggie and run hot tap water through the showerhead for several minutes to remove the loosened mineral deposits and vinegar.
- Scrub your showerhead with an old toothbrush or a scrub brush to remove stubborn mineral build-up. Run cold water through your fixture to rinse out the gunk. Keep scrubbing and rinsing until your showerhead is thoroughly cleaned.
How long to soak shower head in vinegar?
You should let the shower head soak for at least an hour, but preferably over night to let the acid in the vinegar do its job, and dissolve the hard water build up.
The more soiled the showerhead is, the longer you will have to leave it in the vinegar.
- If you are in a hurry, and if the showerhead is made from metal, you can place the pot on the stove and simmer the vinegar for 15 minutes.
- If the showerhead is made from brass, or has a gold or nickel finish, take it out after 30 minutes. You can always give it another vinegar bath once you have rinsed it off.
How to clean your showerhead with vinegar and baking soda
If you have a fixed shower head that you can’t remove for cleaning, you can still use vinegar to remove the hard water deposits from the sprayer. To clean a fixed shower nozzle, you’ll need a plastic bag, rubber band, vinegar, and baking soda.
Make sure that the plastic bag is free of holes and is one that can support the weight of the vinegar for an extended period. Pour enough vinegar into the bag to completely cover the shower head. Pour about 1/3 cup baking soda for every cup of white vinegar that you pour into the bag.
Raise the bag up to the shower head and submerge the shower head completely. Tie off the top of the bag using the rubber band, twist tie, or zip tie, or an elastic band. You want to make sure to secure the bag tightly so that it stays in place when you remove your hands.
Allow the bag to stay on the shower head for at least an hour. The longer you leave the showerhead immersed in the vinegar, the cleaner it will get. Remove the bag and run the shower with hot water for several minutes until it no longer smells like vinegar.
Showerheads often spray unevenly because their tiny holes have gotten plugged with mineral deposits. In order for water to flow freely, you need to remove these deposits. To do that, you may want to soak the showerhead in vinegar. And that may mean removing the showerhead from the shower arm.
Over time, mineral deposits and other gunk can clog spray holes, robbing you of a pleasant shower and increasing the amount of time it takes to remove soap and shampoo due to lackluster pressure.
Bacteria on dirty shower heads could cause sickness, especially in weak immune systems: study. … An analysis of 50 showerheads from nine U.S. cities found that about 30 percent harbored high levels of Mycobacterium avium — a group of bacteria that can cause lung infections when inhaled or swallowed.
So we hope you enjoyed our article giving you the absolute best tips on how to clean your shower head with vinegar and baking soda optionally.